|
|
|
|
Item # HX-916U02800T, 916 Series High Watt Density Draft Barrier Heaters
|
|
|
|
|
|
The 916 Series high watt density draft barrier heaters are designed to fit under large windows to prevent cold down drafts. The heater provides total or supplemental heating for a variety of applications.
- Installation Options : Units may be wall mounted or installed on the floor using pedestal kits. Custom lengths, blank sections and inside or outside corners are available for wall-to-wall installations. Units can be ordered with smooth finish when the back of the heater is visible. These units are not for residential use in the United States.
- Choice of Colors : Heaters can be matched to any decor. White or almond is standard and a wide range of optional colors and custom finishes, including anodized aluminum, are also available.
All models listed are single-phase.
|
|
|
|
|
|
|
Power
|
|
2800 W
|
|
|
|
Voltage Rating
|
|
480 V
|
|
|
|
Total Amps
|
|
5.8 A
|
|
|
|
Heater Length
|
|
94.5 inches
2400 mm
|
|
|
|
Weight
|
|
31.5 lbs
14.3 kg
|
|
|
|
Finish Options
|
|
A - Almond
W - White
|
|
|
|
Factory Built-in Options
|
|
D1 - Disconnect Switch, Three-pole, 600 V, 40 Amp
D3 - Disconnect Switch, Double-pole, 277 V, 20 Amp
L - Custom Length
M1 - High Altitude Automatic Cutout
R1 - 24 V Relay, 240 V, 22 Amp; 277 V, 19 Amp
R2 - 24 V Relay with Transformer, 240 V, 22 Amp; 277 V, 19 Amp
R6 - Pneumatic Relay, 480 V, 25 Amp
R7 - 24 V Proportional Relay
S - Smooth Finish on Heater Back
T1 - Tamperproof Thermostat, Single-pole, 240 V, 25 Amp; 600 V, 10 Amp
T2 - Tamperproof Thermostat, Double-pole, 240 V, 25 Amp; 600 V, 10 Amp
T5 - Adjustable Thermostat, Single-pole, 277V, 25 Amp; 600V, 10 Amp with off position
T6 - Adjustable Thermostat, Double-pole, 277 V, 25 Amp; 600V, 10 Amp with off position
|
|
|
|
Field-Installed Options
|
|
916-166753 - Inside Corner
916-166754 - Outside Corner
916-166756 - Square Pedestal Kit, 3",Qty=2
916-166757 - Splice Plate 2" Long
916-166758 - Finish Joint for Heater with Pedestal
916-166759 - 24V Relay Kit, 240 V, 22 Amp; 277 V, 19 Amp
916-166760 - 24 V Relay Kit with Transformer, 208 V, 22 Amp
916-166761 - 24 V Relay Kit with Transformer, 240 V, 22 Amp
916-166762 - 24 V Relay Kit with Transformer, 277 V, 19 Amp
916-264350 - Adjustable, Single-pole Thermostat Kit 240V, 25 Amp; 600V, 10 Amp with off position
916-264351, Adjustable, Double-pole, Thermostat Kit, 240V, 25 Amp; 600V, 10 Amp, with off position
916B-XXX - Blank Section (specify length in inches-XXX)
|
|
|
|
|
|
- Heating Elements - Two stainless steel elements with aluminum fins float on high temperature nylon bushings for quiet operation. Average watt density is 355 W/ft (1165 W/m).
- Housing - Cabinet is constructed of 18-gauge steel with a 14-gauge aluminum front and top covers. The unit has an epoxy-polyester powder paint finish in white or almond. End caps are provided on all units.
- Inlet/Outlet Grilles - The fresh air inlet is located on the bottom of the unit. The top outlet grille has openings less than 0.25 inches to discourage tampering with the heating element (pencil-proof).
- Built-in Controls - Linear limit, automatic reset thermal cutout.
- Electrical Connection - Each heater has a junction box located at the right end and a built-in full length wireway.
- Installation Requirements - Minimum installation height above the floor is three inches. Field or factory-installed low voltage relay and thermostat kits fit into the right-hand junction box only.
|
|
|
|
- Commercial Buildings
- Hospitals
- Entryways
- Shopping Centers
- Hallways
|
|
|
|
|
|
|
|
|
|
|
|
|
|
