Heatrex custom manufactures TUBULAR & FINNED TUBULAR
HEATING ELEMENTS, IMMERSION
HEATERS, DUCT HEATERS,
UNIT HEATERS & CIRCULATION
HEATERS
Products Tubular & Finned Tubular
Heating Elements
Electric Immersion
Heaters
Enclosure Heaters/
Switchgear Heaters
Process Duct Heaters Circulation Heaters Refrigeration Defrost
Heaters
Bolt Heaters/Flexible
Heaters
HVAC Electric Duct
Heaters
Unit and Comfort Heaters Explosion-Proof Heaters Impedance Heating
Systems
Blog
Heatrex
P.O. Box 515,
Meadville, PA 16335
Phone: (814) 724-1800
Fax: (814) 333-6580
E-mail: sales@heatrex.com
www.heatrex.com Privacy  |  Sitemap
All Categories > Unit and Comfort Heaters > Forced-Air Heaters > 940 Series Hybrid Convection Wall Heater > Item # HX-940U02000J  
Download PDF Download PDF     Printable Page     Email Email This Page     Save To Favorites Save To Favorites

Item # HX-940U02000J, 940 Series Hybrid Convection Wall Heater



The 940 Series wall heater is a unique design and offers two levels of heating. The first level is convection heat with a second level of forced-air heating. This feature combines the quiet operation of convection heating for normal heating conditions and when needed a boost to forced-air heating with greater heating capacity, all in the same unit. This is well suited for condominiums when an up scale appearance is required.
  • Unique Temperature Control: Built-in digital thermostat with full modulating power for convection to fan-forced heating. The power level is automatically managed by the thermostat through the full output of the heater. The electronic thermostat displays actual room temperature, with adjustable temperature settings between 50 and 95°F (10 to 35°C). When the heater is on, four graduated lines indicate the power level on the display.
  • Manual Power Boost: To override the automatic temperature control the heater can be easily switched into the boost heat level using the built-in timer. Boost power can be set for 5, 10, 15, 20, 25 or 30 minutes.
  • Mounting: The heater can be recessed in a 2-inch by 3-inch stud wall, surface mounted or surface mounted with a color matched surface mounting box.





Specifications  · Standard Construction Features  · Applications

Specifications

Power

2000 W

Voltage Rating1

240 V

Total Amps

8.30 A

Weight

22.8 lbs
10.3
kg

Finish Options

A - Almond
W - White

Factory Built-in Options

D3 - Disconnect Switch, 277V, Double-pole, 16 Amp

Field-Installed Options

940-213895 - Cast Aluminum Surface Mounting Box
1 1 Phase


Standard Construction Features
  • Heating Elements – Instant heat nickel-chrome coil resistant wire element.
  • Outlet Grille – Heavy cast aluminum front cover with steel bar inlet and outlet grilles has a polyester powder paint finish available in white or almond.
  • Built-in Controls – Digital display electronic thermostat with timer, automatic reset thermal cutout, temperature sensor and LED night light with on-off switch.
  • Fan motor – Whisper-quiet squirrel-cage fan with factory-lubricated motor.
  • Installation Requirements – Do not install heater covered with vinyl. Maintain a minimum of 4-inches (102 mm) clearance below heater, 1-inch (25 mm) to adjacent walls and 48-inches (1219 mm) in front of heater.
  • Rough In Dimensions – All heaters: 18-5/8” wide x 13-3/8” high x 2-3/4” deep.



Applications
  • Entryways
  • Fire Station Changing Areas
  • Offices
  • Reception Areas
  • Restrooms




 MORE IMAGES 

·  Dimensional Drawings


 DOWNLOADS 

940 Series Submittal
(DOC, 759KB)

Unit Heaters Limited Warranty
(PDF, 90KB)

Unit Heaters Color Selection Chart
(PDF, 86KB)

IOM
(PDF, 675KB)


Heatrex