Heatrex custom manufactures TUBULAR & FINNED TUBULAR
HEATING ELEMENTS, IMMERSION
HEATERS, DUCT HEATERS,
UNIT HEATERS & CIRCULATION
HEATERS
Products Tubular & Finned Tubular
Heating Elements
Electric Immersion
Heaters
Enclosure Heaters/
Switchgear Heaters
Process Duct Heaters Circulation Heaters Refrigeration Defrost
Heaters
Bolt Heaters/Flexible
Heaters
HVAC Electric Duct
Heaters
Unit and Comfort Heaters Explosion-Proof Heaters Impedance Heating
Systems
Blog
Heatrex
P.O. Box 515,
Meadville, PA 16335
Phone: (814) 724-1800
Fax: (814) 333-6580
E-mail: sales@heatrex.com
www.heatrex.com Privacy  |  Sitemap
All Categories > Unit and Comfort Heaters > Baseboard/Convector Heaters > 916 Series High Watt Density Draft Barrier Heaters > Item # HX-916U02100V  
Download PDF Download PDF     Printable Page     Email Email This Page     Save To Favorites Save To Favorites

Item # HX-916U02100V, 916 Series High Watt Density Draft Barrier Heaters



The 916 Series high watt density draft barrier heaters are designed to fit under large windows to prevent cold down drafts. The heater provides total or supplemental heating for a variety of applications.
  • Installation Options : Units may be wall mounted or installed on the floor using pedestal kits. Custom lengths, blank sections and inside or outside corners are available for wall-to-wall installations. Units can be ordered with smooth finish when the back of the heater is visible. These units are not for residential use in the United States.
  • Choice of Colors : Heaters can be matched to any decor. White or almond is standard and a wide range of optional colors and custom finishes, including anodized aluminum, are also available.
    All models listed are single-phase.





Specifications  · Standard Construction Features  · Applications

Specifications

Power

1577 W
2100
W

Voltage Rating

208 V
240
V

Total Amps

7.6 A
8.8
A

Heater Length

70.9 inches
1800
mm

Weight

24.6 lbs
11.1
kg

Finish Options

A - Almond
W - White

Factory Built-in Options

D1 - Disconnect Switch, Three-pole, 600 V, 40 Amp
D3 - Disconnect Switch, Double-pole, 277 V, 20 Amp

L - Custom Length

M1 - High Altitude Automatic Cutout

R1 - 24 V Relay, 240 V, 22 Amp; 277 V, 19 Amp

R2 - 24 V Relay with Transformer, 240 V, 22 Amp; 277 V, 19 Amp

R6 - Pneumatic Relay, 480 V, 25 Amp

R7 - 24 V Proportional Relay

S - Smooth Finish on Heater Back

T1 - Tamperproof Thermostat, Single-pole, 240 V, 25 Amp; 600 V, 10 Amp

T2 - Tamperproof Thermostat, Double-pole, 240 V, 25 Amp; 600 V, 10 Amp

T5 - Adjustable Thermostat, Single-pole, 277V, 25 Amp; 600V, 10 Amp with off position

T6 - Adjustable Thermostat, Double-pole, 277 V, 25 Amp; 600V, 10 Amp with off position

Field-Installed Options

916-166753 - Inside Corner
916-166754 - Outside Corner

916-166756 - Square Pedestal Kit, 3",Qty=2

916-166757 - Splice Plate 2" Long

916-166758 - Finish Joint for Heater with Pedestal

916-166759 - 24V Relay Kit, 240 V, 22 Amp; 277 V, 19 Amp

916-166760 - 24 V Relay Kit with Transformer, 208 V, 22 Amp

916-166761 - 24 V Relay Kit with Transformer, 240 V, 22 Amp

916-166762 - 24 V Relay Kit with Transformer, 277 V, 19 Amp

916-264350 - Adjustable, Single-pole Thermostat Kit 240V, 25 Amp; 600V, 10 Amp with off position

916-264351, Adjustable, Double-pole, Thermostat Kit, 240V, 25 Amp; 600V, 10 Amp, with off position

916B-XXX - Blank Section (specify length in inches-XXX)


Standard Construction Features
  • Heating Elements - Two stainless steel elements with aluminum fins float on high temperature nylon bushings for quiet operation. Average watt density is 355 W/ft (1165 W/m).
  • Housing - Cabinet is constructed of 18-gauge steel with a 14-gauge aluminum front and top covers. The unit has an epoxy-polyester powder paint finish in white or almond. End caps are provided on all units.
  • Inlet/Outlet Grilles - The fresh air inlet is located on the bottom of the unit. The top outlet grille has openings less than 0.25 inches to discourage tampering with the heating element (pencil-proof).
  • Built-in Controls - Linear limit, automatic reset thermal cutout.
  • Electrical Connection - Each heater has a junction box located at the right end and a built-in full length wireway.
  • Installation Requirements - Minimum installation height above the floor is three inches. Field or factory-installed low voltage relay and thermostat kits fit into the right-hand junction box only.




Applications
  • Commercial Buildings
  • Hospitals
  • Entryways
  • Shopping Centers
  • Hallways




 MORE IMAGES 

·  Dimensional Drawing


 DOWNLOADS 

Unit Heaters Limited Warranty
(PDF, 90KB)

Unit Heaters Color Selection Chart
(PDF, 86KB)

916 High Watt Density Draft Barrier
(PDF, 159KB)

916 Series Submittal
(DOC, 622KB)


Heatrex